EBRO ARMATUREN WB 12 Knife Gate Valves Knife Gate Valve These valves are all bi-directional and can therefore be installed into pipe systems independent of pressure direction. Full bore and excellent flow characteristics makes them suitable for fluids, sludge and liquids with solids in suspensions such as water, sewage and bio mass.

KISTLER SCV SWING CHECK VALVE CAST IRON VALVE INDUSTRIAL VALVES KISTLER SWING CHECK VALVE #SCV สวิงเช็ควาล์ว คิสท์เลอร์

KISTLER KLA100L ALUMINUM WAFER BUTTERFLY VALVE INDUSTRIAL VALVES KISTLER ALUMINUM WAFER BUTTERFLY VALVE #KLA100L วาล์วผีเสื้อเวเฟอร์อลูมิเนียม(ด้ามโยก) คิสท์เลอร์

หัวขับวาล์วไฟฟ้า หมุน 90° ให้แรงบิดสูงสุด 500นิวตัน/เมตร นำ้หนักหัวขับ 20kg ชาร์ฟ 36mm ลึก 40mm ISO 5211 F10/F12 เหมาะสำหรับการใช้ร่วมกับ บัตเตอร์ฟลายวาล์วและบอลวาล์ว

STANDARD VERSION Nominal Size: 40mm, 50mm, 63mm, 80mm, 100mm Stainless Steel Case Rugged Construction Dry, Liquid Filled or Dry, but fillable Brass/Copper Alloy Wetted Parts

หัวขับวาล์วไฟฟ้า หมุน 90° ให้แรงบิดสูงสุด 4,500นิวตัน/เมตร น้ำหนักหัวขับ 106kg ชาร์ฟ Ø72mm ลึก 110mm ISO 5211 F16/F25 เหมาะสำหรับการใช้ร่วมกับ บัตเตอร์ฟลายวาล์วและบอลวาล์ว

EBRO ARMATUREN TV Knife Gate Valves Knife Gate Valve Stafsjö’s knife gate valve TV is used as an isolation valve for a transmitter or sensor on a tank for which a short face-to-face length is required.

EBRO ARMATUREN SLX Knife Gate Valves High pressure knife gate valve Stafsjö’s knife gate valves SLH and SLX are designed for the most demanding high pressure applications with slurry and other abrasive media where operation reliability and low life cycle cost are emphasized. The SLH is designed for pressure up 20 bar/290 psi while the SLX is designed for 50 bar/720 psi.

EBRO ARMATUREN SLV Knife Gate Valves Knife Gate Valve for abrasive slurry. Stafsjö’s knife gate valves SLV and SLF are particularly suitable for abrasive and demanding slurry where operation reliability and low life cycle cost are emphasized. The SLV is a lugged version while the SLF is fully flanged and especially suitable on old non-centred pipes or low pressure applications.

EBRO ARMATUREN SLV Knife Gate Valves Knife Gate Valve for abrasive slurry. Stafsjö’s knife gate valves SLV and SLF are particularly suitable for abrasive and demanding slurry where operation reliability and low life cycle cost are emphasized. The SLV is a lugged version while the SLF is fully flanged and especially suitable on old non-centred pipes or low pressure applications.

EBRO ARMATUREN D2G Knife Gate Valves Knife Gate Valve with two plates. Stafsjö’s knife gate valve D2G is a bi-directional tight valve with full bore. The valve is equipped with two hard chromed gates that works towards each other in the bore, which gives an extremely fast operation. This shut-off performance along with its flow characteristics makes it suitable for contaminated media or reject handling. The valve should be mounted only in a vertical pipe line.

EBRO ARMATUREN JT Knife Gate Valves Knife Gate Valve This complete Junk Trap is designed for really tough process conditions handling difficult and abrasive media. The JT is specially designed to minimize turbulence, erosive wear, and build-up of solids and reject material.