EBRO ARMATUREN

EBRO ARMATUREN TV Knife Gate Valves Knife Gate Valve Stafsjö’s knife gate valve TV is used as an isolation valve for a transmitter or sensor on a tank for which a short face-to-face length is required.

EBRO ARMATUREN SLX Knife Gate Valves High pressure knife gate valve Stafsjö’s knife gate valves SLH and SLX are designed for the most demanding high pressure applications with slurry and other abrasive media where operation reliability and low life cycle cost are emphasized. The SLH is designed for pressure up 20 bar/290 psi while the SLX is designed for 50 bar/720 psi.

EBRO ARMATUREN SLV Knife Gate Valves Knife Gate Valve for abrasive slurry. Stafsjö’s knife gate valves SLV and SLF are particularly suitable for abrasive and demanding slurry where operation reliability and low life cycle cost are emphasized. The SLV is a lugged version while the SLF is fully flanged and especially suitable on old non-centred pipes or low pressure applications.

EBRO ARMATUREN SLV Knife Gate Valves Knife Gate Valve for abrasive slurry. Stafsjö’s knife gate valves SLV and SLF are particularly suitable for abrasive and demanding slurry where operation reliability and low life cycle cost are emphasized. The SLV is a lugged version while the SLF is fully flanged and especially suitable on old non-centred pipes or low pressure applications.

EBRO ARMATUREN D2G Knife Gate Valves Knife Gate Valve with two plates. Stafsjö’s knife gate valve D2G is a bi-directional tight valve with full bore. The valve is equipped with two hard chromed gates that works towards each other in the bore, which gives an extremely fast operation. This shut-off performance along with its flow characteristics makes it suitable for contaminated media or reject handling. The valve should be mounted only in a vertical pipe line.

EBRO ARMATUREN JT Knife Gate Valves Knife Gate Valve This complete Junk Trap is designed for really tough process conditions handling difficult and abrasive media. The JT is specially designed to minimize turbulence, erosive wear, and build-up of solids and reject material.

EBRO ARMATUREN RKO Knife Gate Valves Knife Gate Valves for high pressure applications. Stafsjö’s high pressure knife gate valves HP, HPT and HX are all strenthened to withstand high bi-directional pressures. They are equipped with through-going "O" port gates and this secure a really safe and reliable shut-off of static and highly concentrated media. This shut-off performance, along with its excellent flow characteristics, makes them suitable for really demanding operating conditions with media as pulp (pulp concentration < 18%), liqour and highly concentrated slurry.

EBRO ARMATUREN HX Knife Gate Valves Knife Gate Valves for high pressure applications. Stafsjö’s high pressure knife gate valves HP, HPT and HX are all strenthened to withstand high bi-directional pressures. They are equipped with through-going "O" port gates and this secure a really safe and reliable shut-off of static and highly concentrated media. This shut-off performance, along with its excellent flow characteristics, makes them suitable for really demanding operating conditions with media as pulp (pulp concentration < 18%), liqour and highly concentrated slurry.

EBRO ARMATUREN HPT Knife Gate Valves Knife Gate Valves for high pressure applications. Stafsjö’s high pressure knife gate valves HP, HPT and HX are all strenthened to withstand high bi-directional pressures. They are equipped with through-going "O" port gates and this secure a really safe and reliable shut-off of static and highly concentrated media. This shut-off performance, along with its excellent flow characteristics, makes them suitable for really demanding operating conditions with media as pulp (pulp concentration < 18%), liqour and highly concentrated slurry.

EBRO ARMATUREN HP Knife Gate Valves Knife Gate Valve for high pressure applications. Stafsjö’s high pressure knife gate valves HP, HPT and HX are all strenthened to withstand high bi-directional pressures. They are equipped with through-going "O" port gates and this secure a really safe and reliable shut-off of static and highly concentrated media. This shut-off performance, along with its excellent flow characteristics, makes them suitable for really demanding operating conditions with media as pulp (pulp concentration < 18%), liqour and highly concentrated slurry.

EBRO ARMATUREN HG Knife Gate Valves A bi-directional tight Knife Gate Valve with a through-going plate. Stafsjö’s knife gate valves HG have excellent flow characteristics and gives a bi-directional tight sealing.

EBRO ARMATUREN XV Knife Gate Valves Knife Gate Valve Stafsjö’s knife gate valve XV gives a secure and tight shut-off, independent of pressure direction. The valve has good flow characteristics and can be used in applications with pulp, biomass and sludge, and the Polyurethane seated version further extend its field of applications to abrasive media.

EBRO ARMATUREN MV Knife Gate Valves Universally applicable Knife Gate Valve. Stafsjö’s knife gate valve MV is used within many different fields of applications. The valve has a gate with a bevel edge that effectively cuts through different media. In closed position the gate is pushed onto the seat which gives a tight and reliable sealing. This special shut-off technique makes the MV valve suitable for both fluids and dry media such as pulp, sludge, biomass, powder and different kinds of waste.

EBRO ARMATUREN WB 14E Knife Gate Valves Stainless Steel Lug Type Knife Gate Valve. Stafsjö’s WB14E knife gate valve is a high performance shut-off valve with superior flow characteristics, offering bi-directional zero leakage shut-off up to 150 psi/10 bar. It is suitable for media such as pulp stock, chemicals, sludge, bio mass, slurry and water. The fully lugged body design is suitable for dead-end services.

EBRO ARMATUREN WB 14 Knife Gate Valves Lug Type Knife Gate Valve for water applications. These valves are all bi-directional and can therefore be installed into pipe systems independent of pressure direction. Full bore and excellent flow characteristics makes them suitable for fluids, sludge and liquids with solids in suspensions such as water, sewage and bio mass.

EBRO ARMATUREN WB 12 Knife Gate Valves Knife Gate Valve These valves are all bi-directional and can therefore be installed into pipe systems independent of pressure direction. Full bore and excellent flow characteristics makes them suitable for fluids, sludge and liquids with solids in suspensions such as water, sewage and bio mass.

EBRO ARMATUREN ViDos CONTAINER VALVE SPECIAL APPLICATIONS Vibrating Disc keeps products in motion A wafer type process valve with a vibrator mounted on the lower shaft. The disc is set into linear vibrations before opening to keep the product in motion thus reducing compression. The frequency is controlled via air pressure.

EBRO ARMATUREN Inflas CONTAINER VALVE SPECIAL APPLICATIONS Low wear through inflatable liner The sealing system was developed for use with highly abrasive or very sensitive media.Available for all resilient seated butterfly valves with replaceable liner.

EBRO ARMATUREN Cycle Lock CONTAINER VALVE SPECIAL APPLICATIONS EBRO cycle-locks are installed where powdered media is discharged from silos, receiver tanks and bigbags and dosed in many cases. They are also used for feeding into downstream production processes, as well as for inertisation of products during transfer operations.

EBRO ARMATUREN CK-M CONTAINER VALVE SPECIAL APPLICATIONS pipe system valve The metallic sealing version (CK-M) has an airspace between disc and body. This series is highly suited to control airflows and aspiration services.

EBRO ARMATUREN TW-M CONTAINER VALVE SPECIAL APPLICATIONS butterfly valve The series TW-M provides a light metal body with a stainless steel insert ring instead of an elastomer seat. Due to its special design a jamming of the media e.g.granulates is avoided. The valve closes properly.

EBRO ARMATUREN FS-M CONTAINER VALVE SPECIAL APPLICATIONS impeller valve The impeller valve series FS is designed for a safe and consistent discharge of rapid flowing products in the bulk industry.

EBRO ARMATUREN K016 CONTAINER VALVE SPECIAL APPLICATIONS plastic valve A plastic valve with socket ends for low pressure applications in plastic pipes.

EBRO ARMATUREN QV CONTAINER VALVE SPECIAL APPLICATIONS pinch valve A pinch valve to be used in bulk loaded wastewater or slurries.

EBRO ARMATUREN Q 011 CONTAINER VALVE SPECIAL APPLICATIONS Safety valve Q011 double seat valves are designed for isolation/control in high purity air applications.

EBRO ARMATUREN CK CONTAINER VALVE SPECIAL APPLICATIONS Pipe system valve A butterfly valve designed with both ends suitable for clamping rings.

EBRO ARMATUREN TW 150/TW 200 CONTAINER VALVE SPECIAL APPLICATIONS wafer type butterfly valve These valves are designed to be used with tankers silos and road vehicles.

EBRO ARMATUREN TW 80/TW 100 CONTAINER VALVE SPECIAL APPLICATIONS wafer type butterfly valve These valves are designed to be used with tankers silos and road vehicles.

EBRO ARMATUREN BE 250/BE 300 CONTAINER VALVE SPECIAL APPLICATIONS container valve A valve Series especially designed to be used with silos and containers.

EBRO ARMATUREN HP 114-K3 High Performance Valves High Performance Valves Lug type butterfly valve in double-eccentric construction. Reliable sealing even with extreme temperature and pressure conditions.